Park Tool Bts1 - Bottom Bracket Tapping And Facing Set
A precision tool that provides a piloted means of tapping threads in a bottom bracket shell. Includes English taps 1.370 inch x 24 tpi right hand thread for adjustable cup and 1.370 inch x 24 tpi left hand thread for fixed cup Italian thread taps 36mm x 24 tpi right hand thread are also available After...
Park Tool Ccp22c - Crank Puller/ Extractor Tool
The benchmark crank puller of the cycle industry for over 25 yearsThe CCP-22 uses a long comfortable handle and extra fine thread that provides the leverage required to remove even the tightest cranksUnique floating-tip design hasbeen updated over the CCP-2 and ensures even smoother operation...
An accurate way to check for wear of roller and pin on chains1% of wear is enough to affect chainrings and sprockets and allow shifting performance to deteriorateJust insert the chain Checker's pins into two links press the swing arm gauge and then check the gauge window for an accurate readingReads...
Park Tool Chain Wear Indicator
A worn chain shifts poorly and wears sprockets at an accelerated rateThe CC-3 is a Go / No-Go gauge designed to accurately indicate when a chain reaches 0.75% and 1% wear - the point at which most chain manufacturers suggest replacementThe chain should be replaced soon if the 0.75% side fits into...
Park Tool Crank Puller Tool - Extractor For Isis And Octalink Cranks
The CCP-4 Crank Puller is specifically designed to remove crank arms from splined Shimano Octalink and ISIS Drive bottom bracket spindles that do not use a One Key Release systemIt uses a long comfortable handle and a fine thread for the leverage needed to remove tight crank armsUnique rotating...
Park Tool Crown Race Cutting Tool
Perfect headset performance requires accurate machining of the fork crown race and this is the tool to do it. Cuts the outer edge and lower surface of the crown race seat A simple adjusting system allows the tool to be a tight fit on all forks threaded or unthreaded including those with externally butted...
Park Tool Ctp4k - Replacement Chain Tool Pin Set For The Master Chain Tool
A set of four replacement chain tool pins and one ball bearing to make your CT-4 Master Chain Tool as good as new
Park Tool Emergency Tyre Boot - Set Of 3
A reliable self-adhesive patch for emergency tyre repairsHigh strength adhesive developed by 3M keeps the patch where you want itSuper tough film material will survive most conditionsSimply place over the cut or tear on the inside of the tyreCan also be used on tubeless tyre systemsAlways replace...
Park Tool Frame & Forks End Alignment Gauge Set Ffg2
Improperly aligned frame or fork dropouts can cause bent axles and quick-release skewers as well as tracking and shifting problems. The FFG-2 quickly determines whether rear frame or front fork dropouts are aligned and parallel. If an error is detected long handles and comfortable molded grips afford...
A simple brush design that makes it easier to keep your transmission cleanCurved and toothed end for cleaning out between sprocketsStiff nylon bristles for thorough cleaning of derailleurs and chainAlso handy for cleaning behind V-brakes and other hard to reach places
Park Tool Head Cup Remover 1 / 1-1/8 / 1-1/4 Inch
The professional way to remove headset cups. Pulls through headtube until the flared end snaps open behind the headset cup Simply hammer out the cup safely and neatly Fits up to 1-1/4' headtubes and headset cups Heat treated alloy steel with nickel plated finish Made in the USA and covered by Park...
Park Tool Hex Wrench Tool 10mm
Specially designed for cranks Freehubs and pedals the hex tool is built for speed leverage and comfort. The dual density ergonomically designed screwdriver handle provides secure grip and is moulded over an extra long extra deep super strong hex. Also features an additional ball-driver for those really...
Park Tool Htr1b - Head Tube Reaming And Facing Set: 1-1 / 8 Inch Included
The HTR-1B combines reaming and/or facing of the head tube to create a perfect fit for most sizes of headset cups. The HTR-1B comes complete with a 33.8mm reamer and four different size pilots 29.8mm 30.0mm 33.8mm and 36.8mm The reamer is used to clean out or increase the diameter of the head tube Most...
Park Tool Mini Chain Brute Chain Tool Ct-5
A chain tool that is small enough to go anywhere yet which performs like a full size workshop toolFine thread and slide-away T-handle gives plenty of pressure at the pin head to move stubborn chain rivetsIncludes a loosening shelf to release stiff links after assemblyReplaceable driving pin headWorks...
Park Tool Pedal Wrench: 15 Mm & 9/16 Inch
A versatile pedal wrench for regular shop use15 mm and 9/16 inch open endsThe extra long tubular section handle will resist flexing and it is vinyl dipped for comfort and a secure gripMade from Cr-Mo steelReinforced at the spanner openings for a stronger longer life